Lubricant Maintenance — the Fountain of Youth
Preserving oil cleanliness through proper filtration methods pays dividends.
By: Michael Powers
In recent years, the growing emphasis on finding alternative power sources that are renewable, affordable and sustainable have caused tremendous growth in the wind energy industry. Wind turbines, though basic, have key components that are difficult to access and expensive to maintain.
Machinery reliability in wind turbines is especially tasking as poor lubrication practices can cause failures in system gearbox, hydraulic systems and bearings, which are costly to fix. Maintaining clean oil is one of the best investments a company can make to prevent problems, yet contamination often remains an overlooked factor behind premature machinery failure and diminished lubricant life.
To increase scheduled time between maintenance, reduce cost of lubrication replacement, and protect the system from failure, the prevention and treatment of contamination — from the time oil enters a facility until it leaves — is key.
The Problem: Contamination
Two primary types of contamination include dirt and water.
If the atmosphere is contaminated (and most are to some degree), the oil is probably dirty and lubricant quality is compromised. Particulate contamination, once inside an operating system, will accelerate the generation of new contaminants. These contaminants damage critical components and act as a catalyst for oxidation, further degrading lube condition.
If the atmosphere is particularly humid or has frequent temperature fluctuations, the oil is probably moisture-laden and lubricant quality is compromised. Often, plant wash-down activities are responsible for inducing conditions that lead to moisture ingression and corrosion.
The good news is that these factors, which work together to threaten equipment reliability, can be effectively controlled with some preventative maintenance techniques. The best and easiest way to exclude contaminants is to avoid practices that risk exposing lubricants to contaminants.
A multi-faceted program that includes some simple proactive steps will conquer contamination.
The Goal: The Right Targets
Every application is unique — and what’s right for one environment isn’t what’s needed for another. There are a number of sources in which to refer in order to get a bit of help. Noria Corporation, Reliability Web and other publications and manufacturers offer a wide variety of published and training materials that can get you well on your way. To complete an introductory survey, you can visit www.descase.com/contact to request an complementary online self-assessment.
It has been said that prevention is the best cure. Ideally, all of us would have a brand new plant and machinery and begin with a solid program of preventative measures that would ensure the longest life for our equipment and oil. That, of course, never happens. Once you know how big the problem is, you can combine several options to help bring the current situation in line with your cleanliness targets, and add components that will help keep your oil clean and “dry.”
Today’s options for restricting the ingression of contaminants are a far cry from yesterday’s open tube turndown pipes that did little more than keep the birds out (Table 1). Proper installation and maintenance of contamination control breathers can significantly reduce ingression of airborne contaminants.
The breather filter continues to be at the top of the list for preventative maintenance and conquering contamination. Conventional vent ports or breather caps provide little or no protection. They are typically rated at 40 micron and offer no means of capturing moisture. Retrofitting these ports with breathers will provide 24/7 protection against uninvited contaminants, both dirt and water (see Table 2). Clean lubricants extend the life of equipment, and lower the total cost of ownership with lower oil, repair, downtime and maintenance costs (a search for “Lubricant Life Extension Table” on the internet will show a number of sources of information).
Breathing starts the same day the machine is put into operation or a static tank is filled. The correct approach to preventing dirt and moisture damage is to proactively control ingress points. Since the most common point of entry is the conventional vent port, installation of desiccant breathers is imperative.
Breathers are essential to the health of machines and lubricants. A properly fitted and maintained breather is a critical step toward reliability optimization. Combining breather use with other contamination control tools, such as mechanical seals, proper sampling techniques, downstream filters and appropriate lubricant storage/dispensing systems will increase the overall level of maintainability and increase the chances of meeting or even exceeding life expectancies.
In-line / Off-line filtration:
In-line and off-line filtration (sometimes referred to as bypass, kidney-loop, or auxiliary filtration), consists of a motor, pump, filters, and proper hardware connections. Fluid is continuously pumped out of the reservoir, through the filter(s), and back to the reservoir. In-line is, of course, a permanent part of the overall system. An off-line filtration loop has the extra advantage of being relatively easy to retrofit on an existing system that has insufficient filtration. Also, the off-line filtration device can be serviced without turning off the main system.
Filter Carts Capture Contaminants:
A hand cart is a portable, off-line filtration system used to filter fluid inside the reservoir. It is a transfer cart when used to move lubricants from a drum to a reservoir. In either mode, it is an economical solution to off-line filtration requirements.
Filter carts should be used to remove particles and moisture, thereby preserving the working life of the oil. They are not just a tool for emergency remedial measures when dealing with contaminated lubricants and hydraulic fluids. To avoid cross-contamination of fluids, make sure there is a dedicated filter cart for each type of lubricant in use. Filter carts should be fitted with quick disconnects and with particle removal and water — absorbing filter elements. Filter carts should be part of a routine that includes new oil filtering, transferring, and dispensing oils.
New oil filtering, you may ask? Many plant personnel feel new oil is clean enough to use right away. However, many new fluids have initially high contamination levels. Fluids should always be filtered before being put into service. Contamination, both particulate and water, may be added to new fluid during processing, mixing, or handling. This contamination can be removed with the use of a filter cart. They are the ideal way to pre-filter and transfer fluids into reservoirs.
Where To Look: Savings Everywhere
Area #1 – Storage:
Many improvements to your storage procedures can be made with minimal cost. A little time spent simply reviewing your current storage and handling procedures can be informative and useful.
Some simple procedures to improve your storage maintenance operations:
- Stored oil should be kept indoors
- Add breathers to vented storage containers.
- Controlling temperature is important for proper drum storage. Drums “breathe” as the internal pressure increases and decreases with temperature variations. Moisture and other contaminants are forced into the drum when the internal pressure decreases. It is recommended to store drums or containers in enclosed, temperature-controlled storage facilities.
- Shielding storage containers from dirt and moisture is another procedure that will keep your cleaned and filtered oil in good condition. Be as careful with pumps and transfer containers as with your storage containers. This will minimize the chances of cross-contaminating with other lubricants and introducing contaminants into machines when filling.
Area #2 – Handling:
Some simple procedures to improve handling maintenance operations:
- Transfer hoses should be equipped with quick-connects to prevent contamination of the hose from the environment, provide leak-free connections to tanks and reservoirs and allow a method for off-line filtration.
- All oil-dispensing equipment, including tanks, drums, pails, hoses and reels, should be clearly labeled to avoid cross-contamination of products. Color-coding is helpful in avoiding cross-contamination.
- The use of an industrial filter cart is one of the most economical ways to protect your system from destruction caused by contamination.
Area #3 – Equipment:
Nearly every industrial application is a candidate for a contamination control solution. Gearboxes, pumps, turbines, transformers, hydraulic systems... all of them can be looked at as an opportunity to save money through the reduction of downtime, increased oil life (and decreased oil replacement and disposal costs), and increased machinery life and reliability. Examining seals, ensuring the application has the correct sized breather for the application and environment, and the regular filtration of oil can extend the life as much as four times what a non-systematic approach would yield, saving tens if not hundreds of thousands of dollars.
The Payoff: Money In The Bank (And Budget)
Contamination control is the single greatest opportunity for gains in the average lube program. Significant gains in machinery reliability can be made with minimal investments.
Your program’s effectiveness can be measured through the following metrics:
- Maintenance of targeted ISO cleanliness codes
- Reduction in moisture levels (% or ppm) measured by Karl Fischer titration
- Lubricant life extension, extended drain intervals
- Extension of MTBF (mean time between failures), decreased unscheduled downtime
- Cost savings (e.g. reduced component repair, decreased oil disposal expense, decreased oil purchases)
There is an inverse relationship between lubrication quality and maintenance costs. Financial gains can be made by implementing procedures which maximize lubrication effectiveness
There are a good number of documented examples of the effectiveness of using these methods. Maintenance publications and textbooks list case studies from plants around the world that have brought “youth” back to their equipment. There’s the case of the water treatment plant in Ohio that saved money by just adding one type of breather to their equipment, or the bulk storage application that went from an ISO cleanliness rating of 21/19/17 to 18/16/14 with a 20 percent reduction in moisture by using these methods, or the mobile equipment that went over 30,000 hours without needing an oil change.
The Bottom Line
Tribological losses can be greatly reduced through proper lubrication maintenance which effectively starts with breather protection, off-line filtration, and oil sampling. In today’s competitive market with ever climbing oil prices, it is more important than ever to maintain system integrity and extend equipment life.
By utilizing options outlined above and implementing several contamination control techniques, maintaining clean, dry lubricants is easier than ever.